Driver categories
- BIOS
- Bluetooth
- Card Readers
- Digital Camera, Webcam
- DVD, Blu-Ray Players
- Firmware
- Graphics Board
- HDD, SSD, NAS, USB
- Joystick, Gamepad
- Keyboard & Mouse
- Mobile Phones
- Modem
- Monitor
- Motherboard
- Network Card
- Other Drivers & Tools
- Printer, Scanner
- Router, Switch, AP
- Sound Card
- Tablets
- TV, HDTV, Projectors
- TV Tuner, Capture Card
- VoIP
- Audio/DJ Gear
- Network / IP / NVR / Surveillance / Baby Camera
- Gaming Consoles
- Smartwatch / Wearables / Fitness
- Drone / Helicopter / Multicopter / Controller
Search
Download NETGEAR GS748TPS Switch Firmware 5.2.0.10 driver
NETGEAR GS748TPS Switch Firmware 5.2.0.10
The operating system should automatically install the appropriate driver NETGEAR GS748TPS Switch Firmware 5.2.0.10 to your NETGEAR device. If this has not happened, without a manual NETGEAR GS748TPS Switch Firmware 5.2.0.10 driver installation your device may not work properly or may not use all of its features. Download the NETGEAR GS748TPS Switch Firmware 5.2.0.10 driver and install it on your computer - if the device still is not working properly, read the information further down the site about the NETGEAR device from the Firmware category. There you will find helpful tips on how to install the NETGEAR GS748TPS Switch Firmware 5.2.0.10 driver. You will also learn why it is so important to have current NETGEAR drivers.
Driver details
| Operating System | / OS Independent | |
| File size | 4.1 MB | |
| WWW | www.netgear.com | |
| Category: | NETGEAR • Firmware | |
| Number of downloads | 427 | |
| Last update / Date added |
25.07.2014 | |
My device has not been properly installed - what should I do?
After connecting a new NETGEAR device to your computer, the system should automatically install the NETGEAR GS748TPS Switch Firmware 5.2.0.10 driver. If this has not happened, you should take the following steps:
1. Check if the automatic update is enabled
It is the automatic update feature that is responsible for the installation of the Firmware NETGEAR drivers on your computer. If the "UPDATE" feature was disabled, the NETGEAR GS748TPS Switch Firmware 5.2.0.10 driver could not be installed.
It is worth noting that in order for the automatic update to work, the computer must be connected to the Internet (perhaps when connecting the NETGEAR device the computer temporarily did not have the Internet connection or a WiFi signal was weak making it impossible to download the NETGEAR GS748TPS Switch Firmware 5.2.0.10 driver). To make sure, disconnect now and reconnect the NETGEAR device again, and maybe this time the driver will be downloaded.
2. Install the driver manually
This solution may seem more complicated - but it is nothing further from the truth. Just download the NETGEAR GS748TPS Switch Firmware 5.2.0.10 driver and start the installation (keeping in mind that the NETGEAR device must be at the same time connected to the computer). After the installation of the NETGEAR GS748TPS Switch Firmware 5.2.0.10 driver, the device should work properly.
The update of the NETGEAR device driver which is not working properly
It is very important that the NETGEAR devices connected to your computer had their current drivers installed. Without current NETGEAR GS748TPS Switch Firmware 5.2.0.10 drivers there is a greater risk of the device malfunction, of the reduction in security, and there is a possibility of the total damage of the NETGEAR device. Manufacturers from time to time issue new versions of the NETGEAR GS748TPS Switch Firmware 5.2.0.10 software, repairing the errors they find that may cause problems with the NETGEAR devices. Therefore, if you notice that a new version of the NETGEAR GS748TPS Switch Firmware 5.2.0.10 driver is available, you should install it immediately.
Similar drivers from the NETGEAR category
| Driver name | Driver details |
|---|---|
9.9 MB / OS Independent |
|
10.3 MB / OS Independent |
|
10.8 MB / OS Independent |
|
15.1 MB / OS Independent |
|
15.9 MB / OS Independent |
|
| Show all drivers by Firmware NETGEAR | |